|
Pike Brio 3/6-03 |
|
CG |
107mm |
Hook : apx:
103mm from leading edge |
|
Surface/acting as |
Mode |
Direction |
Travel |
|
|
Aileron/Aileron |
start |
up |
16mm |
all measured
at wing tip, 40% expo |
|
|
speed |
up |
16mm |
|
|
|
Thermal |
up |
16mm |
|
|
|
start |
down |
8mm |
|
|
|
speed |
down |
8mm |
|
|
|
thermal |
down |
6mm |
|
|
Flap/Aileron |
start |
up |
7mm |
all measured
at wing root |
|
|
speed |
up |
7mm |
|
|
|
thermal |
up |
7mm |
|
|
|
start |
down |
6mm |
|
|
|
speed |
down |
6mm |
|
|
|
thermal |
down |
6mm |
|
|
Aileron/Crow |
All |
up |
9mm |
at tip |
|
Flap/Crow |
All |
down |
90degr |
at root |
|
Elevator/crow mix V-tail |
All |
down |
2/4mm |
measurement
at half/full crow at ele tip. |
|
Elevator |
All |
up |
6mm |
all measured
at tip, 40% expo |
|
Elevator |
Speed |
up |
6mm |
all max
movement -9/+10 (ele/rud togheter) |
|
Elevator |
All |
down |
5mm |
|
|
Elevator |
Speed |
down |
5mm |
|
|
Rudder |
Speed |
up |
7mm |
40% expo. no
combi switch other than in start and F3F |
|
Rudder |
thermal |
up |
7mm |
40% expo. no
combi switch other than in start and F3F |
|
Rudder |
Speed |
down |
5mm |
40% expo. no
combi switch other than in start and F3F |
|
Rudder |
thermal |
down |
5mm |
40% expo. no
combi switch other than in start and F3F |
|
Speed flap (flap) |
speed |
up |
2-4mm ? |
Equal along
all trailing edge |
|
Speed flap (ail) |
speed |
up |
apx 1,5mm |
Measured at tip |
|
Speed flap (ele) |
speed |
down |
0-0,5mm |
|
|
Start flap (flap) |
start |
down |
10mm |
Equal along
all trailing edge |
|
Start flap (ail) |
start |
down |
apx 6mm |
|
|
Start flap (ele) |
start |
down |
0,5mm |
Can be -0,5mm depending on hook and CG |
|
Thermal flap (flap) |
thermal |
down |
0-3mm |
Equal along
all trailing edge |
|
Thermal flap (ail) |
thermal |
down |
0-..mm |
|
|
snap flap (flap) |
good
air |
down |
4mm |
|
|
Snap flap (ail) |
good
air |
down |
3,5mm |
Equal to flap |
|
|
|
|
|
|
X-tail: (picture) |
|
|
|
|
|
Elevator |
neutral |
|
89,5mm |
Measured on top of steel rod and below tail. See
picture |
|
Elevator |
start/speed |
|
88,5mm |
If used in start the hook needs to be apx 103mm |
|
Elevator |
crow |
|
86/85mm |
measured at half/full crow with aileron only 7mm up |
|
Elevator |
All |
up/down |
94/85mm
(82 w/crow) |
Servo arm
might need to be long if not fast servo is used. |
|
Rudder |
All |
left/right |
apx 30mm |
apx 10mm
combi-switch while launching |
|
|
|
|
|
